Additive and traditionally manufactured components : a comparative analysis of mechanical properties /

Bibliographic Details
Main Author:	Pelleg, Joshua
Corporate Author:	ScienceDirect (Online service)
Format:	eBook
Language:	English
Published:	Amsterdam : Elsevier, 2020.
Subjects:	Additive manufacturing. Electronic books.
Online Access:	Connect to the full text of this electronic book

Table of Contents:

Intro
Additive and Traditionally Manufactured Components: A Comparative Analysis of Mechanical Properties
Copyright
Dedication
Contents
Preface
About the author
Chapter One: What is additive manufacturing?
Chapter Two: Fabrication
2.1. Fused deposition method (FDM)
2.1.1. Melt properties
2.1.2. Liquefier
2.1.3. Heat convection
2.1.4. Pressure drop estimation
2.1.5. Layer deposition and stability
2.1.6. Road spreading
2.1.7. Road cooling and polymer bonding
2.2. Powder-bed fusion (PBF)
2.3. Inkjet printing
2.4. Stereolithography (SLA)
2.4.1. The state of the resin (photopolymer)
2.4.2. The maximum cure depth
2.4.3. The cured line width
2.4.4. Laser scan velocity
2.5. Direct energy deposition (DED)
2.5.1. Thermal model
2.6. Laminated object manufacturing (LOM)
References
Further reading
Chapter Three: Testing: Comparison of AM data with traditionally fabricated
3.1. Tensile tests
3.1.1. Ti-6Al-4V: AM tensile properties
3.1.2. Al alloy AA6061: AM tensile properties
3.1.2.1. Conventionally produced (AM) AA6061
3.1.3. Stainless steel 304L: AM tensile properties
3.1.3.1. Conventionally produced SS 304L
3.1.4. Ceramic
3.1.4.1. AM alumina
3.1.4.2. Conventionally fabricated alumina
3.2. Compression tests
3.2.1. Ti-6Al-4V
3.2.2. Conventionally fabricated Ti-6Al-4V
3.2.3. Al alloys-Al 60613
3.2.4. Conventionally fabricated Al 6061
3.2.5. AM stainless steel 304L
3.2.5.1. Conventionally fabricated stainless steel 304L
3.2.6. Ceramics-Alumina
3.2.7. Conventionally fabricated alumina (Al2O3)
3.2.7.1. Effect of orientation and temperature
3.3. Indentation (hardness)
3.3.1. Ti-6Al-4V
3.3.1.1. Conventionally produced Ti-6Al-4V
3.3.2. Aluminum alloy (Al6061)
3.3.3. Conventionally fabricated Al 6061
3.3.4. Stainless steel 304L
3.3.4.1. Conventionally produced 304L stainless steel
3.3.5. Alumina
3.3.6. Conventionally produced alumina
3.3.6.1. Temperature dependence
3.3.6.2. Hardness of coatings
3.3.6.3. Hardness of alumina films
References
Further reading
Chapter Four: Dislocations in AM and traditional manufacturing: A comparison
4.1. Introduction
4.1.1. In AM Ti-6Al-4V
4.1.2. In traditionally fabricated Ti-6Al-4V
4.1.3. Motion of dislocations
4.2. Introduction AA6061
4.2.1. AM of AA6061 Al alloy
4.2.2. Dislocations in conventionally produced Al AA6061
4.2.2.1. Pinning of dislocations in 6061
4.2.2.2. The strain effect in 6061
4.3. In stainless steel 304L
4.3.1. Introduction
4.3.2. In AM 304L stainless steel
4.3.3. In conventionally fabricated 304L stainless steel
4.4. In alumina (Al2O3)
4.4.1. In conventionally fabricated alumina
References
Further reading
Chapter Five: Deformation in AM and traditional manufacturing: A comparison
5.1. Introduction