Cover Image

Effective width of curved sheet after buckling.

Bibliographic Details
Corporate Author:	United States. National Advisory Committee for Aeronautics
Format:	Government Document eBook
Language:	English
Published:	[Washington] : [s.n.], 1938.
Subjects:	Weights and measures. Airplanes. Aeronautics > Research. Mathematical models.
Online Access:	Electronic resource (PDF)

Similar Items

Experimental studies of the effective width of buckled sheets.
Published: (1936)

The impact on floats or hulls during landing as affected by bottom width.
Published: (1936)

A method of estimating the critical buckling load for structural members.
Published: (1939)

Behavior of plate strip under shear and compressive stresses beyond buckling limit.
Published: (1938)

Working charts for determination of propeller thrust at various air speeds.
Published: (1933)

Computation of 2-dimensional flow in laminar boundary layer.
Published: (1934)

Theoretical span loading and moments of tapered wings produced by aileron deflection.
Published: (1937)

On theory of laminar boundary layers involving separation.
Published: (1934)

Analysis of 2-spar cantilever wings with special reference to torsion and load transference.
Published: (1934)

Analysis and model tests of autogiro jump take-off.
Published: (1936)

Stability of thin℗-walled tubes under torsion.
Published: (1933)

Estimation of moments of inertia of airplanes from design data.
Published: (1936)

Theoretical study of the moment on a body in compressible fluid.
Published: (1939)

Aerodynamic analysis of autogiro rotor with comparison between calculated and experimental results.
Published: (1934)

Pack method for compressive tests of thin specimens of materials used in thin-wall structures.
Published: (1938)

Load tests on stiffened circular cylindrical shell.
Published: (1938)

Vibration response of airplane structures.
Published: (1934)

Effect of spray strips on take℗--off performance of model of flying-boat hull.
Published: (1934)

Pressure drop in tubing in aircraft instrument installations.
Published: (1937)

Piloting technique for recovery from spins.
Published: (1936)

Effect of changes in tail arrangement upon spinning of low-wing monoplane model.
Published: (1936)

Influence of tip shape on wing load distribution as determined by flight tests.
Published: (1934)

Considerations of the take-off problem.
Published: (1936)

Tank tests of 3 models of flying-boat hulls of pointed℗--step type with different angles of dead rise, N. A. C. A. model 35 series.
Published: (1936)

Remarks on elastic axis of shell wings.
Published: (1936)

Measurement of true dynamic and static pressures in flight.
Published: (1939)

Procedure for determining speed and climbing performance of airships.
Published: (1936)

Tank tests of model of NC flying-boat hull, N. A. C. A. model 44.
Published: (1936)

Charts expressing time, velocity, and altitude relations for airplane diving in standard atmosphere.
Published: (1937)

Effects of elevator nose shape, gap, balance, and tabs on aerodynamic characteristics of horizontal tail surface.
Published: (1939)

Tank tests of models of flying boat hulls having longitudinal steps.
Published: (1936)

Tank tests of two models of flying-boat hulls to determine effect of ventilating the step.
Published: (1937)

Further measurements of normal accelerations on racing airplanes.
Published: (1936)

General tank test of model of hull of British Singapore IIC flying boat.
Published: (1936)

Study of autogiro rotor-blade oscillations in plane of rotor disk.
Published: (1936)

Circular motion of bodies of revolution.
Published: (1936)

Reduction of aileron operating force by differential linkage.
Published: (1936)

Tank tests of model of hull of Navy PB-1 flying boat, N. A. C. A. model 52.
Published: (1936)

Hydrodynamic tests in N. A. C. A. tank of model of hull of Short Calcutta flying boat.
Published: (1937)

Full-scale span load distribution on tapered wing with split flaps of various spans.
Published: (1937)