| Tag |
First Indicator |
Second Indicator |
Subfields |
| LEADER |
00000ctm a2200000Ka 4500 |
| 001 |
in00001661863 |
| 005 |
20220103134555.0 |
| 007 |
cr unu a |
| 008 |
020402s2001 xx a b 000 0 eng d |
| 035 |
|
|
|a (OCoLC)ocm49503180
|
| 040 |
|
|
|a TXA
|c TXA
|d UtOrBLW
|
| 049 |
|
|
|a TXAM
|a TXAR
|
| 099 |
|
|
|a 2001
|a Thesis
|a C37
|
| 100 |
1 |
|
|a Carter, Jeremy John,
|d 1976-
|
| 245 |
1 |
4 |
|a The static and dynamic characteristics of divergent tapered-bore hole-pattern gas seals /
|c by Jeremy John Carter.
|
| 264 |
|
1 |
|a [Place of publication not identified] :
|b [publisher not identified] ;
|c 2001.
|
| 300 |
|
|
|a xii, 86 leaves :
|b illustrations ;
|c 28 cm.
|
| 336 |
|
|
|a text
|b txt
|2 rdacontent
|
| 337 |
|
|
|a computer
|b c
|2 rdamedia
|
| 338 |
|
|
|a online resource
|b cr
|2 rdacarrier
|
| 500 |
|
|
|a "Major subject: Mechanical Engineering".
|
| 500 |
|
|
|a Vita.
|
| 502 |
|
|
|b M.S.
|c Texas A&M University
|d 2001.
|
| 504 |
|
|
|a Includes bibliographical references (leaves 75-76).
|
| 520 |
|
|
|a Experimental data is presented for three hole-pattern annular gas seals with differing diverging tapers machined in them. The holes are approximately 3.12 mm (.123 in) deep on average with a hole area to surface area ratio of 43%. The L/d ratio of the seals is approximately 0.75. Taper designs for the three seals include clearance ratios (CR, exit clearance / inlet clearance) of 1.00 (straight-bore), 1.42, and 2.15. Data is presented for tests taken at 10,200 rpm, 15,200 rpm, and 20,200 rpm and at exit-to-inlet pressure ratios of 40% and approximately 53%. Comparisons are given between the three seals for direct and cross-coupled impedances; mass flow rate and effective stiffness and damping coefficients. Results show that an optimum effective damping is obtained with the medium taper geometry. However, the direct damping values are relatively unchanged. Furthermore, a decrease in effective stiffness with increasing taper angle is observed. The tapered seals displayed significantly higher leakage values than the straight seals, with the 2.15 CR seal showing the highest leakage under all test conditions. Measurement data is compared with theoretical predictions generated with the ISOTSEAL modeling code, using the two-control-volume model developed by Kleynhans and Childs (1997). Impedance data is approximated moderately well by the analytical prediction. Effective stiffness and damping values are closely predicted by theory. Although, peak damping values occur at higher frequencies than predicted. This is likely due to varying hole depths. The 1.42 CR seal performance is better predicted by theory than the 2.15 CR seal.
|
| 530 |
|
|
|a Also available online.
|
| 530 |
|
|
|a Issued also on microfiche from Lange Micrographics.
|
| 650 |
|
4 |
|a Major mechanical engineering.
|
| 856 |
4 |
1 |
|u https://hdl.handle.net/1969.1/ETD-TAMU-2001-THESIS-C37
|z Link to OAKTrust copy
|t 0
|
| 948 |
|
|
|a cataloged
|b h
|c 2002/4/2
|d c
|e eneff
|f 11:40:43 am
|
| 994 |
|
|
|a E0
|b TXA
|
| 999 |
|
|
|a MARS
|
| 999 |
f |
f |
|s 293f6cdf-f6cb-38ee-87c2-d28120b0af93
|i c293ec89-4220-309a-9c88-eafd4e477dec
|t 0
|
| 952 |
f |
f |
|p noncirc
|a Texas A&M University
|b College Station
|c Cushing Memorial Library & Archives
|s cush tdrm
|d Cushing: Theses & Dissertations Microforms (Does not check out)
|t 0
|e 2001 Thesis C37
|h Other scheme
|i computer -- online resource
|
| 952 |
f |
f |
|a Texas A&M University
|b College Station
|c Electronic Resources
|s www_evans
|d Available Online
|t 0
|e 2001 Thesis C37
|h Other scheme
|
| 998 |
f |
f |
|a 2001 Thesis C37
|t 0
|l Available Online
|
| 998 |
f |
f |
|a 2001 Thesis C37
|t 0
|l Cushing: Theses & Dissertations Microforms (Does not check out)
|