Effect of grooves cut on the periphery of a circular hole in bars subjected to tension.

Photoelastic determination of the maximum stress in a circular plate having a square hole and subjected to diametral loading.
by: Seay, Crum Elwyn
Published: (1959)

Finite element analysis of high-speed grooved gas bearings /
by: Faria, Marco Tulio Correa de, 1962-
Published: (1999)

Computational analysis of spiral groove thrust bearings and face seals /
by: Zirkelback, Nicole Lisa, 1973-
Published: (1997)

Failure determination for a laminated composite plate with a circular hole.
by: Ko, Chi-Ren Clarence
Published: (1975)

A photoelastic stress analysis of simply supported circular plates with holes in the centers and subjected to uniform loads along the inner edges.
by: Sweet, Harry Jerome
Published: (1958)

A numerical study of compressible flow in labyrinth seals with rub grooves /
by: Adams, Richard Gordon
Published: (1997)

Effect of liquid viscosity and surface tension on atomization of cross injecting sprays /
by: Son, Sangyoung, 1967-
Published: (1995)

A new three-control-volume theory for circumferentially-grooved liquid seals /
by: Marquette, Olivier Robert, 1971-
Published: (1994)

Analysis and testing for rotordynamic coefficients of grooved turbulent annular seals /
by: Kim, Chang-Ho, 1954-
Published: (1985)

A comparison of theoretical and experimental rotordynamic coefficients for helically grooved annular gas seals /
by: Gansle, Anthony Joseph, 1968-
Published: (1993)

An experimental and computational leakage investigation of labyrinth seals with rub grooves of actual size and shape /
by: Ambrosia, Matthew Stanley, 1976-
Published: (2001)

Effect of back clearance and balance hole upon centrifugal pump performance /
by: Hossain, Syed A., 1972-
Published: (2000)

An investigation of the feasibility of locating the tubes of a radiant heating coil in the groove of matched wood flooring.
by: Tansil, John Thomas
Published: (1949)

The effect of spacing and location of bolt holes of steel flanges for pressure vessels and piping.
by: Hall, Harris Harlan
Published: (1949)

The effect of injection hole geometry on flat plate film cooling and heat transfer /
by: Madsen, Eric Perry, 1969-
Published: (1994)

Effect of film hole location on heat transfer coefficient and film effectiveness of a gas turbine blade /
by: Jiang, Huan Wanda
Published: (1994)

Capillary performance and heat transfer charateristics of the evaporating thin liquid film in a triangular micro groove /
by: Ha, Jeong-Mann, 1959-
Published: (1995)

A linear fluid inertia model for improved prediction of force coefficients in grooved squeeze film dampers and grooved oil seal rings /
by: Delgado-Marquez, Adolfo
Published: (2010)

Investigation of induced thermal behavior due to simple tension.
by: Tenison, Larry Turner
Published: (1970)

The effects of fastener hole defects /
by: Andrews, Scot D., 1967-
Published: (1991)

Stress analysis, by photoelastic methods, of a rectangular bar subjected to a torsion load.
by: Rajagopalan, Tiruchengode Chinnappan
Published: (1961)

The theoretical analysis and experimental investigation of liquid pressure drop and maximum heat transport in trianglular grooves : a study of idealized micro heat pipes /
by: Ma, Hongbin, 1962-
Published: (1995)

A photoelastic study of simply supported rectangular beams with holes on the vertical center lines and subjected to concentrated loads.
by: Lin, Ping Hua
Published: (1965)

The photoelastic determination of the stress distribution across a horizontal cross section of a circular plate having a square hole and subjected to a diametral load applied along a diagonal of the square.
by: Vickers, Richard Herbert
Published: (1959)

Numerical simulation of squeeze film dampers and study of the effect of central groove on the dynamic pressure distribution /
by: Boppa, Praneetha
Published: (2012)

Static and dynamic characteristics for a two-axial-groove bearing and a pressure-dam bearing /
by: Al Jughaiman, Bader K.
Published: (2010)

The photoelastic determination of the principal stresses in polygons having round central holes and subjected to a concentrated diagonal compressive load.
by: Priddy, Tommy Glynn
Published: (1961)

The effect of grit depth of cut on the strength of ground advanced structural ceramics /
by: Fang, Gwo-Ping, 1953-
Published: (1996)

Investigation of the Helix-Grooved Elastomeric Pump /
by: Jacobsen, Kelly Scott
Published: (1982)

Mathematical model of the Texas A&M low-tension oil containment barrier.
by: Fowler, Joe Robert
Published: (1971)

Criterion for failure under reversed transverse shear superimposed upon static tension.
by: Esphahani, Mostafa
Published: (1974)

Rotordynamic coefficients and leakage flow of parallel-grooved liquid-seals /
by: Kilgore, James Joseph
Published: (1988)

The effect of injection hole orientation on flat-plate film cooling and heat transfer using a transient liquid crystal technique /
by: Zapata, Dyrk Oliver
Published: (1994)

The static and dynamic characteristics of divergent tapered-bore hole-pattern gas seals /
by: Carter, Jeremy John, 1976-
Published: (2001)

Rotordynamic evaluation of frequency dependent impedances of hole-pattern gas damper seals /
by: Holt, Christopher George, 1972-
Published: (2000)

Local heat (mass) transfer in a rotating square channel with ejection holes /
by: Yoon, Churl, 1964-
Published: (1999)